The   machine   made   by   15+15   pieces   on   two   parallel   lines.   The   coupling   can   be   either   in   length   or   width   it   is   possible   to   apply   a dryer for demoulds, the “on length” disposition is cheaper for dryer installation. The module consists of: Support bench mould on floor where lower semi-moulds are fixed (concave) Higher cross-lifted which supports upper semi-mould (convex). Lifting system implemented by gear motors, trapezoidal screws. The moulds closing system is mechanical with a pneumatic system to have a perfect fit to the moulds. Casting plant using PVC pipes, supply and distribution valves, stainless steel tank and accessories to use (taps probes etc.). Electrical system with switchboard, protection and control casting cycle. All safety devices provided by the most stringent existing standards and manuals on. The   piece   can   be   extract   easily   by   hand,   even   staying   on   top   (by   placing   under   a   plateau   of   demoulder   and   releasing   it   with a   blast   of   compressed   air)   to   parade   it   from   the   lower   (in   this   case   it   is   necessary   to   choose   define   demoulding   points   or mould pieces to be removed) Deposit bench Considering high piece density the same are deposited on trolleys reducing space of fixed deposit bench, on specific request. Demoulder device Mini Telemachus type To   facilitate   the   extraction   of   the   piece   from   the   lower   moulds,   especially   for   very   large   tanks   or   basins   etc.   You   can   use   the simplified   demoulder   Mini   Telemachus   type.   Thanks,   it   the   lifting   operation   on   the   desired   floor   and   replacing   the   piece   is   fully automatic. It is pneumatic, as also the necessary vacuum to suction sampling achieved by draft gage to Venturi effect. Dryer The dryer, available on request, can be placed on the machine to achieve a double casting daily Permitted uses This   machine   was   made   to   realize   pieces   with   obliged   thickness   (without   drainage)   and   with   two   parts   moulds,   but   it   can   be   also used   to   produce   other   pieces,   always   into   two   parts   and   not   big   size,   realized   with   mould   divided   into   two   parts   such   as   wash basins…
· · · · · · · · CS1/2/3 - CASTING MACHINE FOR TANK RAW MATERIALS AND GLAZES COMPANY CASTING GRINDING MACHINE NEWS CONSUMABLES
CIIsc S.r.l. Via Michelangelo, 4 Civita Castellana (VT) ITALY 01033 TEL.: +39 0761518283 Email: info@ciisc.it
TEST DEVICES
The module consists of: Support    bench    mould    on    floor    where    lower    semi-moulds    are    fixed (concave) Higher cross-lifted which supports upper semi-mould (convex). Lifting system implemented by gear motors, trapezoidal screws. The   moulds   closing   system   is   mechanical   with   a   pneumatic   system   to   have a perfect fit to the moulds. Casting   plant   using   PVC   pipes,   supply   and   distribution   valves,   stainless steel tank and accessories to use (taps probes etc.). Electrical system with switchboard, protection and control casting cycle. All   safety   devices   provided   by   the   most   stringent   existing   standards   and manuals on. The   piece   can   be   extract   easily   by   hand,   even   staying   on   top   (by   placing under     a     plateau     of     demoulder     and     releasing     it     with     a     blast     of compressed   air)   to   parade   it   from   the   lower   (in   this   case   it   is   necessary   to choose define demoulding points or mould pieces to be removed)
· · · · · · · ·
CIIsc S.r.l. Via Michelangelo, 4 Civita Castellana (VT) ITALY 01033                            TEL.: +39 0761518283 Email: info@ciisc.it
HOME HOME